Not showing Fans and Power supplys in 1.12. Works fine in 1.11 running against G10 iLo5

[dasi-git-user]

1.11:
...
...
: Controller HPE Smart Array P408i-a SR Gen10 status is: OK
: Logical Drive Array-raid6 (Array-raid6) 15003GiB (RAID6) status: OK
: Logical Drive SR Volume 65 (SR Volume 65) 8002GiB (None) status: OK
: SmartStorageBattery 1 (charge level: 100%, capacity: 96W) status: OK
: Adapter HPE Ethernet 1Gb 4-port 369i Adapter (FW: 1.3437.0) status: None
: Port 1.1 (type: None, speed: 0, autoneg: None, duplex: half) link: None
: Port 1.2 (type: None, speed: 0, autoneg: None, duplex: half) link: None
: Port 1.3 (type: None, speed: 0, autoneg: None, duplex: half) link: None
: Port 1.4 (type: None, speed: 0, autoneg: None, duplex: half) link: None
: Power supply 1 (720478-B21) status is: OK
: Power supply 2 (720478-B21) status is: OK
: Power redundancy 1 status is: Enabled
: Fan '1' (7%) status is: OK
: Fan '2' (17%) status is: OK
: Fan '3' (17%) status is: OK
: Fan '4' (10%) status is: OK
: Fan '5' (24%) status is: OK
: Fan '6' (24%) status is: OK

1.12:
...
...
: Controller HPE Smart Array P408i-a SR Gen10 status is: OK
: Logical Drive Array-raid6 (Array-raid6) 15003GiB (RAID6) status: OK
: Logical Drive SR Volume 65 (SR Volume 65) 8002GiB (None) status: OK
: SmartStorageBattery 1 (charge level: 100%, capacity: 96W) status: OK
: Adapter HPE Ethernet 1Gb 4-port 369i Adapter (FW: 1.3437.0) status: None
: Port 1.1 (type: None, speed: 0, autoneg: None, duplex: half) link: None
: Port 1.2 (type: None, speed: 0, autoneg: None, duplex: half) link: None
: Port 1.3 (type: None, speed: 0, autoneg: None, duplex: half) link: None
: Port 1.4 (type: None, speed: 0, autoneg: None, duplex: half) link: None

[bb-Ricardo]

Hi, can you please try the next-release branch. It should work with this version.

[dasi-git-user]

Hi, what do you mean. It works with the old 1.11.0. But not if i upgrade to 1.12.0.

…

On Tue, Aug 5, 2025 at 2:56 PM Ricardo ***@***.***> wrote: Hi, can you please try the next-release branch. It should work with this version. — Reply to this email directly, view it on GitHub <#175 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BK36E2FIC3STH66JWOBT74T3MCSYBAVCNFSM6AAAAACDC3QXIWVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTIMBQGYYDINY> . You are receiving this because you authored the thread.Message ID: ***@***.*** com>

[bb-Ricardo]

You can use the git command to change to the fixed version. Try git checkout next-release and then run the command again.

[dasi-git-user]

Works, thanks.